6 m elliptical rotating pole, EA-W100-6, internal halyard, outrigger / gallows arm has the item number 8516.31 and is characterised by nominal height 6 m, pole diameter 100 mm, outrigger, elliptical design. The entry-level price is 788,97 € incl. VAT.
With 6 m of visible height above ground, the pole is the typical choice for company entrances, car dealerships and club grounds. Portrait flags of between 300 and 400 cm in length suit this pole; in landscape format, sizes around 150 × 200 cm work well. The pole is installed in a ground socket cast in concrete; the stated 6 m remain visible above the foundation. Choose the ground socket to match the 100 mm tube diameter. You will find the matching foundation plan in the „Instructions“ tab. At 100 mm in diameter, the elliptical tube is made of aluminium. The outrigger arm holds the flag clear of the pole so it stays readable even when there is no wind.
Flagpoles with 360° rotating bearing and hoistable bracket/gallows arm.
Aluminium pole tubes with an elliptical cross-section, optimised structurally and aerodynamically. Besides the greatest possible stability, this tube shape has the advantage of the lowest possible noise emission in strong winds.
Thanks to the structural and aerodynamic optimisation of the pole tubes, the poles guarantee stability in accordance with DIN EN 1991-1-4/NA for wind zone I when flying a flag, up to a nominal height of 12 m. For nominal heights up to and including 9 m, stability for wind zone 2 is guaranteed as standard – likewise when flying a flag.
The benefit of the rotating bearing of the pole tubes is that both the flag and the hoisting device turn "out of the wind" at the same time. This prevents the flag from wrapping or tangling in turbulent wind and rain.
Nominal height 6.00 m, total length 6.80 m
Aluminium pole tube, material EN AW-6082T6, silver anodised E6/EV1, profile cross-section 100 x 113 mm, elliptical, aerodynamically and structurally optimised, with a moulded groove for the internal hoisting device, internal halyard with PES rope, lockable operating point with a flush-fitting stainless steel cover with lever lock, pull slide, flag fabric holders (5 pcs.), telescopic bracket 100/160 cm, keder flags can be hoisted, pole tube mounted on a plug-in shaft with rotating bearing, steel ground socket Ø 76.1 x 8 mm, 0.8 m deep with 3 adjusting screws M12 for vertical pole installation, pole weight 54 kg
Nominal height (NH): 6.00 m, total length (GL): 6.80 m, profile cross-section: 100/113
Side tape with hooks. Hollow hem along the top edge of the fabric, Ø 30 mm, open on both sides. The topmost hook must be sewn on directly below the hollow hem. Hook spacing max. 1.00 m, max. fabric width 1.50 x 4 m. The flag is slid onto the bracket tube by its hollow hem. The topmost flag carabiner hooks into the hole of the long slide, the remaining carabiners into the eyelets of the flag fabric holders. The flag weight with stainless steel carabiner is hooked into the lowest flag fabric holder and thus prevents the flag from riding up in gusts.
The steel ground socket is included in the price.
With a first order this accessory is already included in the set – you do not need to order it separately.
| Nominal height in m | Flag size in cm |
| 5 | 80x200 |
| 6 | 100x300 |
| 7 | 150x350 |
| 8 | 100x400 |
| 9 | 120x500 |
| 10-12 | larger |
| Nominal height in m | Flag size in cm |
| 5 | 120x80 |
| 6 | 150x120 |
| 7 | 180x120 |
| 8 | 200x120 |
| 9 | 225x150 |
| 10 | 250x150 |
| 12 | 300x200 |
Question not listed? All questions & answers · or call us: 09833 98894-0
